1,120
edits
Cumulus.ini (preserving history): Difference between revisions
Cumulus.ini (preserving history) (view source)
Revision as of 21:46, 30 August 2009
, 30 August 2009Added links to various other Cumulus Wiki pages
m (Logging=1 VP2SleepInterval WS2300Sync VPClosedownTime APRSHumidityCutoff and EWduplicatecheck added to [Station] section) |
m (Added links to various other Cumulus Wiki pages) |
||
|
|-
|Type=-1
|Station Type as set by the checked radio box in the [[Cumulus_Screenshots#Configuration_Menu_Screens|Station Configuration Screen]], Station Type block
*0=Vantage Pro
|Confirm you wish to close Cumulus application after telling it to close
*0 = Disabled, application will close immediately
*1 = Enabled, application will prompt for
|-
|CloseOnSuspend=1
|-
|UseCumulusForecast=0
|From the Station Configuration Screen Forecast block, if selected Cumulus will generate a simple weather forecast, if your station does not supply one, or as an alternative to the one supplied by your station. See the [[Forecast webtag]] for more information.
*0 = Disabled (default)
*1 = Enabled
|-
|EWTempdiff=x.y
|Enter this line in the [Station] section of the Cumulus.ini to filter
|-
|RTdisconnectcount=60
|-
|Logging=1
|Add to cumulus.ini [Station] section to have Cumulus start with [[debug]] logging on
|-
|VP2SleepInterval=x
|-
|APRSHumidityCutoff=1
|Add to [Station] section For Scientific technical It doesn't report humidity to [[APRS]] when the temperature is below -10°C
|-
|EWduplicatecheck=0
|-
|[Web Site]
|Section Name - the following parameters
|-
|ForumURL=<nowiki>http://sandaysoft.com/forum/</nowiki>
|Set in the Internet Configuration Screen Web Settings block.
*0 = Disabled
*1 = Enabled, Cumulus will upload a file called [[realtime.txt]] to your web site, at the interval specified by Realtime Interval (see below). This file contains various weather parameters and is used by the CumulusRealtime.swf real time wind gauges (as on the supplied 'gauges' web page. If you don't have this option selected, but do have the 'auto update' option set (and a suitable interval configured), Cumulus will still create the realtime.txt file at the specified Interval (not the Realtime Interval) so that you can specify it as an extra file to upload during the 'normal' upload, or use it for any other purpose on your PC.
|-
|RealtimeInterval=3000
|-
|Background=12632256
|Decimal value for the Graph background
|-
|WindColour=65535
|Decimal value for the 10 minute average wind speed plot
|-
|GustColour=8421376
|Decimal value for the Wind Gust plot
|-
|RainColour=9527753
|Decimal value for the Rain plot
|-
|RainTodayColour=9527753
|Decimal value for the Rain Today plot
|-
|TempColour=9527753
|Decimal value for the Temperature plot
|-
|HeatIndexColour=16711680
|Decimal value for the Heat Index plot
|-
|PressColour=9527753
|Decimal value for the Pressure plot
|-
|WindDirColour=255
|Decimal value for the Wind Direction plot
|-
|DewPointColour=255
|Decimal value for the Dew Point plot
|-
|WindChillColour=32768
|Decimal value for the Wind Chill plot
|-
|MinTempColour=16711680
|Decimal value for the Minimum Temperature plot
|-
|MaxTempColour=255
|Decimal value for the Maximum Temperature plot
|-
|AvgTempColour=32768
|Decimal value for the Average Temperature plot
|-
|DailyRainColour=32768
|Decimal value for the Daily Rain plot
|-
|InsideTempColour=0
|Decimal value for the Inside Temperature plot
|-
|InsideHumColour=255
|Decimal value for the Inside Humidity plot
|-
|OutsideHumColour=16711680
|Decimal value for the Outside Humidity plot
|-
|Graph3D=0
|-
|WindSpeedMult=1
|Multiplier by which measured Average [[Wind_measurement|Wind Speed]] to be corrected. Officially wind speed is measured with sensors at 10m above ground level. If your sensor is not at 10m AGL then a correction multiplier should be applied using the following formula ''V10/Vh = 1/(0.233 + 0.656*log10(h+4.75))'' where "h" is your sensor height in meters.
e.g. if your anemometer is 5m off the ground, V10/Vh comes out at 1.134
|-
| |||