Cumulus.ini (preserving history): Difference between revisions

Cumulus.ini (preserving history) (view source)

Revision as of 17:41, 6 September 2013

590 bytes added , 6 September 2013

m

→‎Section: Offsets: Clarify that multiplier affects rainfall rate too; Clarify offset too

Sfws

5,838

edits

Revision as of 08:36, 6 September 2013 (view source) Sfws (talk \| contribs) m (→‎Section: Station: Revised 'DataLogInterval' note) ← Older edit		Revision as of 17:41, 6 September 2013 (view source) Sfws (talk \| contribs) m (→‎Section: Offsets: Clarify that multiplier affects rainfall rate too; Clarify offset too) Newer edit →
\|- \|style="background:lightgray;"\|[Offsets] \|style="background:lightgray;"\|Section Name - the following 'attribute=value' parameters are the ~~correction~~adjustment factors for your specific sensors \|- \|PressOffset=0Offset_Value \|Default 'Offset_Value' is 0 in this parameter used for formula: Cumulus pressure = Measured Pressure + 'Offset_Value' ~~\|Value by which Measured Pressure to be corrected (Add/Subtract)~~ \|- \|TempOffset=0Offset_Value \|Default 'Offset_Value' is 0 in this parameter used for formula: Cumulus Outdoor Temperature = Measured Outdoor Temperature + 'Offset_Value' ~~\|Value by which Measured Outdoor Temperature to be corrected (Add/Subtract)~~ \|- \|HumOffset=0Offset_Value \|Default 'Offset_Value' is 0 in this parameter used for formula: Cumulus Humidity = Measured Humidity + 'Offset_Value' ~~\|Value by which Measured Humidity to be corrected (Add/Subtract)~~ \|- \|WindDirOffset=0Offset_Value \|Default 'Offset_Value' is 0 in this parameter used for formula: Cumulus Wind Bearing = Measured Wind Bearing + 'Offset_Value' ~~\|Value by which Measured Wind Direction to be corrected (Add/Subtract)~~ \|- \|InTempOffset=0 Offset_Value \|Default 'Offset_Value' is 0 in this parameter used for formula: Cumulus Indoor Temperature = Measured Indoor Temperature + 'Offset_Value' ~~\|Value by which Measured Indoor Temperature to be corrected (Add/Subtract)~~ \|- \|WindSpeedMult=1 \|Multiplier by which measured Average [[Wind_measurement#~~Compensation~~Wind_Speed\|Wind Speed]] is to be corrected. Officially in UK the wind speed is measured with sensors at 10m above ground level. If your sensor is not at 10m AGL then a correction multiplier should be applied using the following formula ''V10/Vh (default= 1~~/(0.233 + 0.656log10(h+4.75~~)~~)'' where "h" is your sensor height in meters~~. ~~e.g. if your anemometer is 5m off the ground, V10/Vh comes out at 1.134~~ e.g. Officially in UK the wind speed is measured with sensors at 10m above ground level. If your sensor is not at 10m AGL then a correction multiplier should be applied using the following formula ''V10/Vh = 1/(0.233 + 0.656log10(h+4.75))'' where "h" is your sensor height in meters so if your anemometer is 5m off the ground, V10/Vh comes out at 1.134 \|- \|WindGustMult=1 \|Multiplier by which measured [[Wind_measurement#Wind_Speed\|Wind Gust]] Speed is to be corrected (default=1). \|- \|TempMult=1 \|Multiplier by which measured Temperature is to be corrected (default=1). \|- \|HumMult=1 \|Multiplier by which measured Humidity is to be corrected (default=1). \|- \|RainMult=1 \|Multiplier by which measured Rainfall (and therefore rainfall rate too) is to be corrected (default=1). \|- \|UVOffset=0Offset_Value \|Default 'Offset_Value' is 0 in this parameter used for formula: Cumulus UV level = Measured UV level + 'Offset_Value' ~~\|Value by which measured UV to be corrected (add/subtract).~~ \|- \|UVMult=1 \|Multiplier by which measured UV to be corrected (default=1). \|}