5,838
edits
Category:Cumulus MX: Difference between revisions
m
→MySQL settings
m (→MySQL settings) |
m (→MySQL settings) |
||
|
*2. ''Custom upload - at rollover''
** In the previous option, you have no ability to vary the schema, it will update a column for Total Evaporation even if your weather station cannot calculate that. It will update columns for total hours of sunshine, highest solar radiation level, and the maximum UV in the day even if you cannot measure these. It will not record whether snow was falling or lying, or the depth of snow
** MX provides this alternative option, again doing an upload as part of roll over to next day ([[#MX_End_of_Day_Process|sequence shown below]], the Custom EOD SQL is run after the day reset to new date, but before the dayfile.txt update with existing values and so before today.ini to yesterday.ini processing).
**In this section you can specify the schema, and say which columns are to be updated with three selections:
**# Save - a button after all option sections, until you click it any changes you make in this section have no effect
**# A tick box to enable or disable this upload (so you can leave the SQL recorded, but stop running it when you like.
**# The SQL you want to run, what you type in this small text box should include INSERT IGNORE (or REPLACE) to insert a row, or include UPDATE to change columns in a row that already exists, like any SQL it must include the name of the table, the columns to be updated, and the values you want to insert into the columns are either expressed as web tags, as SQL functions on web tags, or as a sub-query reading the values from somewhere else.
**#* Here is an example of a suitable query that MX can process for you [note I have had to include some yesterday tags e.g. for primary key ('''<#metdateyesterday format=yyyy-MM-dd>''', and I have used the SUBSTRING function at one point, but I don't have a sub-query in this example):
<pre>INSERT IGNORE INTO `test_daily_summary` (`MaxRainRate`, `TMaxRainRate`, `HighHourRain`, `THighHourRain`, `TotRainFall`, `SnowFalling`, `SnowLying`, `SnowDepth`, `CumChillHours`, `LogDate`, `RollOver`, `MinTemp`, `TMinTemp`, `HeatDegDays`, `AvgTemp`, `MaxTemp`, `TMaxTemp`, `CoolDegDays`, `LowDewPoint`, `TLowDewPoint`, `LowHum`, `TLowHum`, `HighHum`, `THighHum`, `HighDewPoint`, `THighDewPoint`, `GreatWindChill`, `TGreatWindChill`, `LowAppTemp`, `TLowAppTemp`, `HighAppTemp`, `THighAppTemp`, `HighHeatInd`, `THighHeatInd`, `MinPress`, `TMinPress`, `MaxPress`, `TMaxPress`, `HighAvgWSpeed`, `THighAvgWSpeed`, `StrongestWindGust`, `TStrongestWindGust`, `BearStrongestWindGust`, `BearStrongestWindGustSym`,`BearDomWind`, `BearDomWindSym`, `TotWindRun`) VALUES ('<#rrateTM>', '<#TrrateTM>', '<#hourlyrainTH>', '<#ThourlyrainTH>', '<#rfall> ', '<#snowfalling>', '<#snowlying>', '<#snowdepth>', '<#chillhours>', '<#metdateyesterday format=yyyy-MM-dd>', '(1 * SUBSTRING(<#rollovertime>,0,2))', '<#tempYL>', '<#TtempYL> ', '<#heatdegdays> ', '<#avgtemp>', '<#tempTH>', '<#TtempTH> ', '<#cooldegdays> ', '<#dewpointTL>', '<#TdewpointTL>', '<#humTL>', '<#ThumTL>', '<#humTH>', '<#ThumTH>', '<#dewpointTH>', '<#TdewpointTH>', '<#wchillTL>', '<#TwchillTL>', '<#apptempTL>', '<#TapptempTL>', '<#apptempTH>', '<#TapptempTH>', '<#heatindexTH>', '<#TheatindexTH>', '<#pressTL>', '<#TpressTL>', '<#pressTH>', '<#TpressTH>', '<#windTM>', '<#TwindTM>', '<#wgustTM>', '<#TwgustTM>', '<#bearingTM>', '<#directionTM>', '<#domwindbearing>', '<#domwinddir>', '<#windrun>');</pre>
** Again before you enable this option, there is a facility lower down this setting page (under the heading '''Create database table''') where you can type some SQL to be run immediately, that can create the table you want this option to update, (although it could even populate any table with historic data, it is only intended for a small query). I am using a table that already exists as I have used it for testing changes to my PHP scripts, so I did not need to create a table before I enabled the query shown above.
| |||